ESPHome-Devices

Xiaomi Mi Desklamp 1S

Xiaomi Mi Desklamp 1S

Device Type: light
Electrical Standard: eu

substitutions:
friendly_name: Mi Desk Lamp 1S Room
device_name: mi-desklamp-1s-room
# Basic Config
esphome:
name: ${device_name}
comment: ${friendly_name}
platform: ESP32
board: esp32doit-devkit-v1
platformio_options:
platform: espressif32@3.4.0
platform_packages:
- tasmota/framework-arduinoespressif32 @ 3.10006.210420
# WiFi connection
wifi:
ssid: !secret wifi_ssid
password: !secret wifi_password
ap:
ssid: ${device_name}
password: !secret ap_password
ap_timeout: 1min
use_address: ${device_name}.local
manual_ip:
static_ip: 192.168.XXX.X
gateway: 192.168.XXX.X
subnet: 255.255.255.0
captive_portal:
# Enable logging
logger:
# Enable Home Assistant API
api:
password: !secret api_password
# Enable over-the-air updates
ota:
password: !secret ota_password
# Enable Web server
web_server:
port: 80
# Sync time with Home Assistant
time:
- platform: homeassistant
id: homeassistant_time
# Text sensors with general information
text_sensor:
- platform: version
name: ${friendly_name} Version
- platform: wifi_info
ip_address:
name: ${friendly_name} IP Address
sensor:
# Uptime sensor
- platform: uptime
name: ${friendly_name} Uptime
# WiFi Signal sensor
- platform: wifi_signal
name: ${friendly_name} Wifi Signal
update_interval: 60s
# Mi Desk Lamp 1S Config
- platform: rotary_encoder
id: rotation
pin_a: GPIO26
pin_b: GPIO27
resolution: 2
on_value:
then:
- if:
condition:
# Check if Button is pressed while rotating
lambda: "return id(button).state;"
then:
# If Button is pressed, change CW/WW
- lambda: |-
auto min_temp = id(light1).get_traits().get_min_mireds();
auto max_temp = id(light1).get_traits().get_max_mireds();
auto cur_temp = id(light1).current_values.get_color_temperature();
auto new_temp = max(min_temp, min(max_temp, cur_temp + (x*10)));
auto call = id(light1).turn_on();
call.set_color_temperature(new_temp);
call.perform();
else:
# If Button is not pressed, change brightness
- light.dim_relative:
id: light1
relative_brightness: !lambda |-
return x / 25.0;
# Reset Rotation to 0
- sensor.rotary_encoder.set_value:
id: rotation
value: 0
binary_sensor:
- platform: gpio
id: button
pin:
number: GPIO33
inverted: True
mode: INPUT_PULLDOWN
on_click:
then:
- light.toggle: light1
output:
- platform: ledc
pin: GPIO2
id: output_cw
frequency: 40000Hz
power_supply: power
- platform: ledc
pin: GPIO4
id: output_ww
power_supply: power
frequency: 40000Hz
power_supply:
- id: power
pin: GPIO12
enable_time: 0s
keep_on_time: 0s
light:
- platform: cwww
id: light1
default_transition_length: 0s
constant_brightness: true
name: "Lights"
cold_white: output_cw
warm_white: output_ww
cold_white_color_temperature: 4800 K
warm_white_color_temperature: 2500 K #2500k is the original value of the lamp. To correct binning for 2700k to look more like 2700k use 2650k instead
restore_mode: ALWAYS_ON
gamma_correct: 0
Edit this page on GitHub