devices.esphome.io

Generic Glass Touch Switch with 1, 2, 3 pole variants

Generic Glass Touch Switch with 1, 2, 3 pole variants

Device Type: switch
Electrical Standard: us
Board: esp8266

General Notes

This config was created based on the 3 pole switch that I had. I'm not sure what the pins for the 4 pole variant would be, but it would not be hard to figure it out if you have the unit.

There is another variant to these switches with LEDs on the buttons. These are called out below.

I labeled the switch as Top/Middle/Bottom as the L1-L4 ports on the rear are actually inverted when installed (L4 on top, L1 on bottom).

Product Images

Front of 3 pole switch alt text

Rear of 3 pole switch alt text

Wiring of switch alt text

GPIO Pinout (Per top to bottom when installed)

PinFunction
GPIO3Button, Top
GPIO4Relay, Top (Labeled L4)
GPIO5Button, Middle
GPIO12Button, Bottom
GPIO13Relay, Bottom (Labeled L2)
GPIO15Relay, Middle (Labeled L3)
GPIO16Status LED
GPIO0Status LED (alternative, some switches)
GPIO14LED, Top (some switches)
GPIO1LED, Middle (some switches)
GPIO14LED, Bottom (some switches)

Basic Configuration

substitutions:
platform: ESP8266
board: esp01_1m
device_name: esphome_dining_room_switch
friendly_name: "Dining Room Switch"
reboot_timeout_wifi: 900s
reboot_timeout_api: 1800s
output_power: 17dB
#################################
esphome:
platform: ${platform}
board: ${board}
name: ${device_name}
esp8266_restore_from_flash: true
wifi:
ssid: !secret wifi_iot_ssid
password: !secret wifi_iot_pwd
fast_connect: on
reboot_timeout: ${reboot_timeout_wifi}
output_power: ${output_power}
ap:
ssid: "AP_${friendly_name}"
password: !secret wifi_backup_pwd
api:
reboot_timeout: ${reboot_timeout_api}
ota:
web_server:
port: 80
logger:
#################################
binary_sensor:
- platform: gpio
pin:
number: GPIO14
inverted: True
name: "${friendly_name} Top Button"
id: button_top
on_press:
then:
- if:
condition:
light.is_on: light_top
then:
- light.turn_off: light_top
else:
- light.turn_on: light_top
- platform: gpio
pin:
number: GPIO5
inverted: True
name: "${friendly_name} Middle Button"
id: button_middle
on_press:
then:
- if:
condition:
light.is_on: light_middle
then:
- light.turn_off: light_middle
else:
- light.turn_on: light_middle
- platform: gpio
pin:
number: GPIO12
inverted: True
name: "${friendly_name} Bottom Button"
id: button_bottom
on_press:
then:
- if:
condition:
light.is_on: light_bottom
then:
- light.turn_off: light_bottom
else:
- light.turn_on: light_bottom
output:
- platform: gpio
id: relay_top
pin: GPIO4
- platform: gpio
id: relay_middle
pin: GPIO15
- platform: gpio
id: relay_bottom
pin: GPIO13
- platform: esp8266_pwm
id: status_led
pin:
number: GPIO16
inverted: True
switch:
- platform: restart
name: "Front Door REBOOT"
light:
- platform: binary
output: relay_top
id: light_top
restore_mode: ALWAYS_OFF
name: "${friendly_name} Top"
- platform: binary
output: relay_middle
id: light_middle
restore_mode: ALWAYS_OFF
name: "${friendly_name} Middle"
- platform: binary
output: relay_bottom
id: light_bottom
restore_mode: ALWAYS_OFF
name: "${friendly_name} Bottom"
# icon: "mdi:ceiling-light"
- platform: monochromatic
name: "${friendly_name} Status LED"
output: status_led

Config for alternative variant

substitutions:
platform: ESP8266
board: esp01_1m
device_name: esphome_dining_room_switch
friendly_name: "Living Room Switch"
reboot_timeout_wifi: 900s
reboot_timeout_api: 1800s
output_power: 17dB
#################################
esphome:
platform: ${platform}
board: ${board}
name: ${device_name}
esp8266_restore_from_flash: true
wifi:
ssid: !secret wifi_iot_ssid
password: !secret wifi_iot_pwd
fast_connect: on
reboot_timeout: ${reboot_timeout_wifi}
output_power: ${output_power}
ap:
ssid: "AP_${friendly_name}"
password: !secret wifi_backup_pwd
api:
reboot_timeout: ${reboot_timeout_api}
ota:
web_server:
port: 80
logger:
#################################
status_led:
pin:
number: GPIO0
inverted: true
binary_sensor:
- platform: gpio
pin: GPIO12
name: "l1 switch"
id: switch_1
internal: true
filters:
- invert:
on_press:
- light.toggle:
id: lightsw_1
- platform: gpio
pin: GPIO05
name: "l2 switch"
id: switch_2
internal: true
filters:
- invert:
on_press:
- light.toggle:
id: lightsw_2
- platform: gpio
pin: GPIO3
name: "l3 switch"
id: switch_3
internal: true
filters:
- invert:
on_press:
- light.toggle:
id: lightsw_3
output:
- platform: gpio
pin: GPIO13
id: relay_1
- platform: gpio
pin: GPIO15
id: relay_2
- platform: gpio
pin: GPIO04
id: relay_3
- platform: gpio
pin: GPIO16
id: led_1
inverted: true
- platform: gpio
pin: GPIO01
id: led_2
inverted: true
- platform: gpio
pin: GPIO14
id: led_3
inverted: true
light:
- platform: binary
name: "${friendly_name} Top"
id: lightsw_1
output: relay_1
- platform: binary
name: "${friendly_name} Middle"
id: lightsw_2
output: relay_2
- platform: binary
name: "${friendly_name} Bottom"
id: lightsw_3
output: relay_3
Edit this page on GitHub