devices.esphome.io

Shelly 1

Shelly 1

Device Type: switch
Electrical Standard: euukus
Board: esp8266

Amazon Link

GPIO Pinout

PinFunction
GPIO4Relay
GPIO5Switch Input

Basic Configuration

# Basic Config
esphome:
  name: shelly_1
  platform: ESP8266
  board: esp01_1m


wifi:
  ssid: !secret wifi_ssid
  password: !secret wifi_password


logger:
api:
ota:


# Device Specific Config
output:
  - platform: gpio
    pin: GPIO4
    id: shelly_1_relay


light:
  - platform: binary
    name: "Shelly 1 Light"
    output: shelly_1_relay
    id: lightid


binary_sensor:
  - platform: gpio
    pin:
      number: GPIO5
      #mode: INPUT_PULLUP
      #inverted: True
    name: "Switch Shelly 1"
    on_state:
      then:
        - light.toggle: lightid
    internal: true
    id: switchid

Detached switch mode for push button light switch

This config will send events to Home Assistant so you can use the Shelly as detached switch. The events can be used as triggers for automations to toggle an attached (smart) light, and to perform other actions on double click and long click (e.g. turn off all the lights on the floor, start a "go to bed" automation).

In case there is no connection to Wifi, or no API connection (normally Home Assistant) the config will toggle the relay, so it will still toggle the attached light in cases where Wifi or HA fails.

The relay is exposed to Home Assistant as a switch. As well as some (optional) sensors with information on the ESPHome version and Wifi status

# Basic config


substitutions:
  device_name: Shelly1


esphome:
  name: shelly_detached
  platform: ESP8266
  board: esp01_1m


wifi:
  ssid: !secret wifi_ssid
  password: !secret wifi_pass


  # Enable fallback hotspot (captive portal) in case wifi connection fails
  ap:
    ssid: ${device_name} Hotspot
    password: !secret hotspot_pass


captive_portal:


# Enable logging
logger:


# Enable Home Assistant API
api:


# Enable OTA updates
ota:


# Enable Web server (optional).
web_server:
  port: 80


# Text sensors with general information.
text_sensor:
  # Expose ESPHome version as sensor.
  - platform: version
    name: ${device_name} ESPHome Version
  # Expose WiFi information as sensors.
  - platform: wifi_info
    ip_address:
      name: ${device_name} IP
    ssid:
      name: ${device_name} SSID
    bssid:
      name: ${device_name} BSSID


# Sensors with general information.
sensor:
  # Uptime sensor.
  - platform: uptime
    name: ${device_name} Uptime


  # WiFi Signal sensor.
  - platform: wifi_signal
    name: ${device_name} WiFi Signal
    update_interval: 60s


# Shelly 1 detached switch config with multi click options and fallback in case of wifi or api fail


switch:
  - platform: gpio
    name: shelly1 ${device_name}
    pin: GPIO4
    id: shelly_relay
    restore_mode: restore_default_off


binary_sensor:
  - platform: gpio
    pin:
      number: GPIO5
    name: ${device_name} button
    # config for multi click actions
    on_multi_click:
      # double click
      - timing:
          - ON for at most 1s
          - OFF for at most 1s
          - ON for at most 1s
          - OFF for at least 0.2s
        then:
          - if:
              condition:
                and:
                  - wifi.connected:
                  - api.connected:
              # send double click event in case wifi and api are conncected
              then:
                - homeassistant.event:
                    event: esphome.button_pressed
                    data:
                      title: shelly ${device_name} double click
              # toggle relay in case either wifi or api are not connected
              else:
                - switch.toggle: shelly_relay
        # long click
      - timing:
          - ON for at least 1.5s
        then:
          - if:
              condition:
                and:
                  - wifi.connected:
                  - api.connected:
              # send long click event in case wifi and api are conncected
              then:
                - homeassistant.event:
                    event: esphome.button_pressed
                    data:
                      title: shelly ${device_name} long click
              # toggle relay in case either wifi or api are not connected
              else:
                - switch.toggle: shelly_relay
        # single click
      - timing:
          - ON for at most 1s
          - OFF for at least 0.5s
        then:
          - if:
              condition:
                and:
                  - wifi.connected:
                  - api.connected:
              # send single click event in case wifi and api are conncected
              then:
                - homeassistant.event:
                    event: esphome.button_pressed
                    data:
                      title: shelly ${device_name} short click
              # toggle relay in case either wifi or api are not connected
              else:
                - switch.toggle: shelly_relay
    internal: true
    id: button

Detached switch mode for toggle light switch

This config will send events to Home Assistant so you can use the Shelly as detached switch. The events can be used as triggers for automations to toggle an attached smart light.

In case the relay is switched off, the Shelly has no connection to Wifi, or no API connection to Home Assistant can be made, the config will toggle the relay. This allows the switch to still keep turning the attached smart light on and off when WiFi or Home Assistant is unavailable.

When the power drops and goes back on, the relay will default to off. This prevents lights turning on when a short power outage happens when you are away from home.

The relay is exposed to Home Assistant as a switch. As well as some (optional) sensors with information on the ESPHome version and Wifi status

substitutions:
  device_name: "Switch Light Kitchen"


esphome:
  name: shelly1-kitchen
  platform: ESP8266
  board: esp01_1m


wifi:
  ssid: !secret wifi_ssid
  password: !secret wifi_pass


  # Enable fallback hotspot (captive portal) in case wifi connection fails
  ap:
    ssid: "shelly1 kitchen hotspot"
    password: !secret hotspot_pass


captive_portal:


# Enable logging
logger:


# Enable Home Assistant API
api:


# Enable OTA updates
ota:


# Enable Web server (optional).
web_server:
  port: 80


# Text sensors with general information.
text_sensor:
  - platform: wifi_info
    ip_address:
      name: ${device_name} IP


# Sensors with general information.
sensor:
  # Uptime sensor.
  - platform: uptime
    name: ${device_name} Uptime


  # WiFi Signal sensor.
  - platform: wifi_signal
    name: ${device_name} WiFi Signal
    update_interval: 60s


# Shelly 1 detached switch config with fallback in case of wifi or api fail


switch:
  - platform: gpio
    name: ${device_name}
    pin: GPIO4
    id: shelly_relay
    # after reboot, keep the relay off. this prevents light turning on after a power outage
    restore_mode: ALWAYS_OFF


binary_sensor:
  - platform: gpio
    name: ${device_name} Input
    pin:
      number: GPIO5
    # small delay to prevent debouncing
    filters:
      - delayed_on_off: 50ms
    # config for state change of input button
    on_state:
        then:
          - if:
              condition:
                and:
                  - wifi.connected:
                  - api.connected:
                  - switch.is_on: shelly_relay
              # toggle smart light if wifi and api are connected and relay is on
              then:
                - homeassistant.service:
                    service: light.toggle
                    data:
                      entity_id: light.kitchen
              # else, toggle relay
              else:
                - switch.toggle: shelly_relay
    id: button
Edit this page on GitHub

On this page