devices.esphome.io

Kogan SmarterHome Smart Power Board With USB Ports & Energy Meter

Kogan SmarterHome Smart Power Board With USB Ports & Energy Meter

Device Type: plug
Electrical Standard: au
Board: esp8266

alt text

https://www.kogan.com/au/buy/kogan-smarterhome-smart-power-board-with-usb-ports-energy-meter/

GPIO Pinout

PinFunction
GPIO00Push Button
GPIO01Green LED (Inverted: true)
GPIO13Relay 1
GPIO14Relay 2
GPIO03Relay 3
GPIO15Relay USB
GPIO12HLW8012 SEL Pin
GPIO04HLW8012 CF Pin
GPIO05HLW8012 CF1 Pin

Note: In the below configuration, the push button (and surrounding LED) is configured to only control Relay 3 (End Plug)

Basic Config

substitutions:
device_name: kogan_strip_1
device_ip: 192.168.x.x
plug_icon: mdi:power-socket-au
usb_icon: mdi:usb-port
plug1_restore: ALWAYS_ON
plug2_restore: ALWAYS_OFF
plug3_restore: ALWAYS_OFF
usb_restore: ALWAYS_ON
# Higher value gives lower watt readout
current_res: "0.00250"
# Lower value gives lower voltage readout
voltage_div: "799"
esphome:
name: ${device_name}
platform: ESP8266
board: esp8285
wifi:
ssid: !secret wifi_ssid
password: !secret wifi_password
manual_ip:
static_ip: ${device_ip}
gateway: 192.168.x.x
subnet: 255.255.255.0
logger:
web_server:
port: 80
api:
reboot_timeout: 15min
encryption:
key: !secret encryption_key
ota:
password: !secret ota_password
binary_sensor:
- platform: gpio
pin:
number: GPIO0
mode: INPUT_PULLUP
inverted: true
name: "${device_name}_button"
on_press:
- switch.toggle: relay3
- platform: status
name: "${device_name}_status"
switch:
- platform: gpio
id: green_led
pin:
number: GPIO1
inverted: true
restore_mode: ALWAYS_OFF
- platform: gpio
name: "${device_name}_plug1"
pin: GPIO13
id: relay1
icon: ${plug_icon}
restore_mode: ${plug1_restore}
- platform: gpio
name: "${device_name}_plug2"
pin: GPIO14
id: relay2
icon: ${plug_icon}
restore_mode: ${plug2_restore}
- platform: gpio
name: "${device_name}_plug3"
pin: GPIO3
id: relay3
icon: ${plug_icon}
restore_mode: ${plug3_restore}
on_turn_on:
- switch.turn_on: green_led
on_turn_off:
- switch.turn_off: green_led
- platform: gpio
name: "${device_name}_usb"
pin: GPIO15
id: relayusb
icon: ${usb_icon}
restore_mode: ${usb_restore}
sensor:
- platform: hlw8012
sel_pin:
number: GPIO12
inverted: true
cf_pin: GPIO04
cf1_pin: GPIO05
current:
name: "${device_name}_current"
unit_of_measurement: A
voltage:
name: "${device_name}_voltage"
unit_of_measurement: V
power:
id: ${device_name}_wattage
name: "${device_name}_wattage"
unit_of_measurement: W
current_resistor: ${current_res}
voltage_divider: ${voltage_div}
change_mode_every: 8
update_interval: 15s
- platform: total_daily_energy
name: "${device_name}_daily_energy"
power_id: ${device_name}_wattage
filters:
- multiply: 0.001
unit_of_measurement: kWh
- platform: wifi_signal
name: "${device_name}_rssi"
update_interval: 5min
- platform: uptime
id: uptime_sec
name: "${device_name}_uptime"
update_interval: 5min
text_sensor:
- platform: template
name: "${device_name}_upformat"
lambda: |-
uint32_t dur = id(uptime_sec).state;
int dys = 0;
int hrs = 0;
int mnts = 0;
if (dur > 86399) {
dys = trunc(dur / 86400);
dur = dur - (dys * 86400);
}
if (dur > 3599) {
hrs = trunc(dur / 3600);
dur = dur - (hrs * 3600);
}
if (dur > 59) {
mnts = trunc(dur / 60);
dur = dur - (mnts * 60);
}
char buffer[17];
sprintf(buffer, "%ud %02uh %02um %02us", dys, hrs, mnts, dur);
return {buffer};
icon: mdi:clock-start
update_interval: 5min
time:
- platform: homeassistant
id: homeassistant_time
Edit this page on GitHub