Copy
# Basic Config

substitutions:
  device_name: aoycocr_plug
  device_description: Energy Monitoring Smart Plug with button, blue LED, and red LED.
  friendly_name: Aoycocr-X10S Plug

esphome:
  name: ${device_name}
  comment: ${device_description}
  platform: ESP8266
  board: esp01_1m
  esp8266_restore_from_flash: true #writes each state change to flash for switch or light with restore_mode: RESTORE_DEFAULT_OFF/ON, see https://esphome.io/components/esphome.html#esp8266-restore-from-flash

wifi:
  ssid: !secret wifissid
  password: !secret wifipass
  fast_connect: on #we only have one WiFi AP so just use the first one that matches
  ap: #since we listed an SSID above, this AP mode will only enable if no WiFi connection could be made
    ssid: ${friendly_name}_AP
    password: !secret wifipass

captive_portal:

# Enable logging
logger:
  baud_rate: 0 #disable UART logging

# Enable Home Assistant API
api:

# Enable OTA updates
ota:

# Enable web server
web_server:
  port: 80

# Enable time component for use by daily power sensor
time:
  - platform: homeassistant
    id: homeassistant_time

binary_sensor:
  # Reports when the button is pressed
  - platform: gpio
    device_class: power
    pin:
      number: GPIO13
      inverted: True
    name: ${friendly_name} Button
    on_press:
      - switch.toggle: relay

  # Reports if this device is Connected or not
  - platform: status
    name: ${friendly_name} Status

sensor:
  # Reports the WiFi signal strength
  - platform: wifi_signal
    name: ${friendly_name} Signal
    update_interval: 60s

  # Reports how long the device has been powered (in minutes)
  - platform: uptime
    name: ${friendly_name} Uptime
    filters:
      - lambda: return x / 60.0;
    unit_of_measurement: minutes

  # Reports the Current, Voltage, and Power used by the plugged-in device (not counting this plug's own usage of about 0.7W/0.02A, so subtract those when calibrating with this plugged into a Kill-A-Watt type meter)
  - platform: hlw8012
    sel_pin:
      number: GPIO12
      inverted: True
    cf_pin: GPIO5
    cf1_pin: GPIO14
    current_resistor: 0.001 #The value of the shunt resistor for current measurement. Defaults to the Sonoff POW’s value 0.001 ohm. Verified on https://fccid.io/2AKBP-X10S/Internal-Photos/X10S-Int-photo-4308983 that we use "R001" = 0.001 ohm
    voltage_divider: 2401 #The value of the voltage divider on the board as (R_upstream + R_downstream) / R_downstream. Defaults to the Sonoff POW’s value 2351. From the pic we use 2x "125" = 2x 1.2Mohm for R_upstream and "102" = 1kohm for R_downstream, so (1,200,000+1,200,000+1,000)/1,000 = 2401
    # but those don't fix the measurement values, probably because we actually have a BL0937 chip instead of a HLW8012, (and part variance aswell) so we have to manually calibrate with a known load or a load and a Kill-A-Watt type meter. My values used below will only be +/-10% of yours I think.
    # The comments about the voltage divider were taken from the AWP04L template. I was unable to verify the voltage divider in the Aoycocr X10S plug.
    power:
      name: ${friendly_name} Power
      unit_of_measurement: W
      id: wattage
      filters:
        - calibrate_linear:
            # Map 0.0 (from sensor) to 0.0 (true value)
            - 0.0 -> 0.0 #Need to keep 0 mapped to 0 for when connected device is not drawing any power
            - 67.6 -> 11.0 #Tested using a Kill-A-Watt meter and LED bulb minus 0.7W from just this plug with LED bulb off
    current:
      name: ${friendly_name} Current
      unit_of_measurement: A
      filters:
        - calibrate_linear:
            # Map 0.0 (from sensor) to 0.0 (true value)
            - 0.0 -> 0.0 #Need to keep 0 mapped to 0 for when connected device is not drawing any power
            - 0.12 -> 0.08 #Tested using a Kill-A-Watt meter and LED bulb minus 0.02A from just this plug with LED bulb off
    voltage:
      name: ${friendly_name} Voltage
      unit_of_measurement: V
      filters:
        - calibrate_linear:
            # Map 0.0 (from sensor) to 0.0 (true value)
            - 0.0 -> 0.0
            - 322.4 -> 118.3 #Tested using a Kill-A-Watt meter, value while connected LED bulb was on
    change_mode_every: 1 #Skips first reading after each change, so this will double the update interval. Default 8
    update_interval: 10s #20 second effective update rate for Power, 40 second for Current and Voltage. Default 60s

  # Reports the total Power so-far each day, resets at midnight, see https://esphome.io/components/sensor/total_daily_energy.html
  - platform: total_daily_energy
    name: ${friendly_name} Total Daily Energy
    power_id: wattage
    filters:
      - multiply: 0.001 ## convert Wh to kWh
    unit_of_measurement: kWh

text_sensor:
  # Reports the ESPHome Version with compile date
  - platform: version
    name: ${friendly_name} ESPHome Version

switch:
  - platform: gpio
    name: ${friendly_name}
    pin: GPIO4
    id: relay
    restore_mode: RESTORE_DEFAULT_OFF #Try to restore relay state after reboot/power-loss event.
    #RESTORE_DEFAULT_OFF (Default) - Attempt to restore state and default to OFF if not possible to restore. Uses flash write cycles.
    #RESTORE_DEFAULT_ON - Attempt to restore state and default to ON. Uses flash write cycles.
    #ALWAYS_OFF - Always initialize the pin as OFF on bootup. Does not use flash write cycles.
    #ALWAYS_ON - Always initialize the pin as ON on bootup. Does not use flash write cycles.
    on_turn_on:
      - light.turn_on:
          id: blue_led
          brightness: 100%
    on_turn_off:
      - light.turn_off: blue_led

output:
  - platform: esp8266_pwm
    id: red_output
    pin: GPIO0
    inverted: True
  - platform: esp8266_pwm
    id: blue_output
    pin: GPIO2
    inverted: True

light:
  - platform: monochromatic
    name: ${friendly_name} Red LED
    output: red_output
    id: red_led
    restore_mode: ALWAYS_OFF #Start with light off after reboot/power-loss event.
    #RESTORE_DEFAULT_OFF (Default) - Attempt to restore state and default to OFF if not possible to restore. Uses flash write cycles.
    #RESTORE_DEFAULT_ON - Attempt to restore state and default to ON. Uses flash write cycles.
    #ALWAYS_OFF - Always initialize the pin as OFF on bootup. Does not use flash write cycles.
    #ALWAYS_ON - Always initialize the pin as ON on bootup. Does not use flash write cycles.
    effects:
      - strobe:
      - flicker:
          alpha: 50% #The percentage that the last color value should affect the light. More or less the “forget-factor” of an exponential moving average. Defaults to 95%.
          intensity: 50% #The intensity of the flickering, basically the maximum amplitude of the random offsets. Defaults to 1.5%.
      - lambda:
          name: Throb
          update_interval: 1s
          lambda: |-
            static int state = 0;
            auto call = id(red_led).turn_on();
            // Transtion of 1000ms = 1s
            call.set_transition_length(1000);
            if (state == 0) {
              call.set_brightness(1.0);
            } else {
              call.set_brightness(0.01);
            }
            call.perform();
            state += 1;
            if (state == 2)
              state = 0;
  - platform: monochromatic
    name: ${friendly_name} Blue LED
    output: blue_output
    id: blue_led
    restore_mode: ALWAYS_OFF #Start with light off after reboot/power-loss event.
    #RESTORE_DEFAULT_OFF (Default) - Attempt to restore state and default to OFF if not possible to restore. Uses flash write cycles.
    #RESTORE_DEFAULT_ON - Attempt to restore state and default to ON. Uses flash write cycles.
    #ALWAYS_OFF - Always initialize the pin as OFF on bootup. Does not use flash write cycles.
    #ALWAYS_ON - Always initialize the pin as ON on bootup. Does not use flash write cycles.
    effects:
      - strobe:
      - flicker:
          alpha: 50% #The percentage that the last color value should affect the light. More or less the “forget-factor” of an exponential moving average. Defaults to 95%.
          intensity: 50% #The intensity of the flickering, basically the maximum amplitude of the random offsets. Defaults to 1.5%.
      - lambda:
          name: Throb
          update_interval: 1s
          lambda: |-
            static int state = 0;
            auto call = id(blue_led).turn_on();
            // Transtion of 1000ms = 1s
            call.set_transition_length(1000);
            if (state == 0) {
              call.set_brightness(1.0);
            } else {
              call.set_brightness(0.01);
            }
            call.perform();
            state += 1;
            if (state == 2)
              state = 0;

# Blink the red light if we aren't connected to WiFi. Could use https://esphome.io/components/status_led.html instead but then we couldn't use the red light for other things as well.
interval:
  - interval: 500ms
    then:
      - if:
          condition:
            not:
              wifi.connected:
          then:
            - light.turn_on:
                id: red_led
                brightness: 100%
                transition_length: 0s
            - delay: 250ms
            - light.turn_off:
                id: red_led
                transition_length: 250ms

Copy
# Common code for Aoycocr X10S plugs

esphome:
  name: ${device_name}
  comment: ${device_description}
  platform: ESP8266
  board: esp01_1m

wifi:
  ssid: !secret wifissid
  password: !secret wifipass
  use_address: ${ipaddress}

  # Enable fallback hotspot (captive portal) in case wifi connection fails
  ap:
    ssid: ${friendly_name}_AP
    password: !secret fallbackpass

captive_portal:

# Enable logging
logger:
  baud_rate: 0 #disable UART logging

# Enable Home Assistant API
api:
  encryption:
    key: !secret api_encryption_key

# Enable OTA updates
ota:
  password: !secret esphomeotapwd

# Enable web server
web_server:
  port: 80

# Enable time component for use by daily power sensor
time:
  - platform: homeassistant
    id: homeassistant_time

binary_sensor:
  # Reports when the button is pressed
  - platform: gpio
    device_class: power
    pin:
      number: GPIO13
      inverted: True
    name: ${friendly_name} Button
    on_press:
      - switch.toggle: relay

  # Reports if this device is Connected or not
  - platform: status
    name: ${friendly_name} Status

sensor:
  # Reports the WiFi signal strength
  - platform: wifi_signal
    name: ${friendly_name} Signal
    update_interval: 60s

  # Reports how long the device has been powered (in minutes)
  - platform: uptime
    name: ${friendly_name} Uptime
    filters:
      - lambda: return x / 60.0;
    unit_of_measurement: minutes

  # Reports the Current, Voltage, and Power used by the plugged-in device (not counting this plug's own usage of about 0.8W/0.019A, so subtract those when calibrating with this plugged into a Kill-A-Watt type meter)
  - platform: hlw8012
    sel_pin:
      number: GPIO12
      inverted: True
    cf_pin: GPIO5
    cf1_pin: GPIO14
    current_resistor: 0.001 #The value of the shunt resistor for current measurement. Defaults to the Sonoff POW’s value 0.001 ohm. Verified on https://fccid.io/2AKBP-X10S/Internal-Photos/X10S-Int-photo-4308983 that we use "R001" = 0.001 ohm
    voltage_divider: 2401 #The value of the voltage divider on the board as (R_upstream + R_downstream) / R_downstream. Defaults to the Sonoff POW’s value 2351. From the pic we use 2x "125" = 2x 1.2Mohm for R_upstream and "102" = 1kohm for R_downstream, so (1,200,000+1,200,000+1,000)/1,000 = 2401
    # but those don't fix the measurement values, probably because we actually have a BL0937 chip instead of a HLW8012, (and part variance aswell) so we have to manually calibrate with a known load or a load and a Kill-A-Watt type meter. My values used below will only be +/-10% of yours I think.
    # The comments about the voltage divider were taken from the AWP04L template. I was unable to verify the voltage divider in the Aoycocr X10S plug.
    power:
      name: ${friendly_name} Power
      unit_of_measurement: W
      id: wattage
      filters:
        - calibrate_linear:
            # Map 0.0 (from sensor) to 0.0 (true value)
            - 0.0 -> 0.0 #Need to keep 0 mapped to 0 for when connected device is not drawing any power
            - ${wattage_calibration} #Tested using a Kill-A-Watt meter and LED bulb minus 0.7W from just this plug with LED bulb off
    current:
      name: ${friendly_name} Current
      unit_of_measurement: A
      filters:
        - calibrate_linear:
            # Map 0.0 (from sensor) to 0.0 (true value)
            - 0.0 -> 0.0 #Need to keep 0 mapped to 0 for when connected device is not drawing any power
            - ${amperage_calibration} #Tested using a Kill-A-Watt meter and LED bulb minus 0.02A from just this plug with LED bulb off
    voltage:
      name: ${friendly_name} Voltage
      unit_of_measurement: V
      filters:
        - calibrate_linear:
            # Map 0.0 (from sensor) to 0.0 (true value)
            - ${voltage_calibration1} #Don't care if 0 reading aligns with 0 real Volts since we won't ever measure that
            - ${voltage_calibration2} #Tested using a meter, value while connected LED bulb was on
    change_mode_every: 1 #Skips first reading after each change, so this will double the update interval. Default 8
    update_interval: 10s #20 second effective update rate for Power, 40 second for Current and Voltage. Default 60s

  # Reports the total Power so-far each day, resets at midnight, see https://esphome.io/components/sensor/total_daily_energy.html
  - platform: total_daily_energy
    name: ${friendly_name} Total Daily Energy
    power_id: wattage
    filters:
      - multiply: 0.001 ## convert Wh to kWh
    unit_of_measurement: kWh

text_sensor:
  # Reports the ESPHome Version with compile date
  - platform: version
    name: ${friendly_name} ESPHome Version

switch:
  - platform: gpio
    name: ${friendly_name}
    pin: GPIO4
    id: relay
    restore_mode: RESTORE_DEFAULT_OFF #Try to restore relay state after reboot/power-loss event.
    #RESTORE_DEFAULT_OFF (Default) - Attempt to restore state and default to OFF if not possible to restore. Uses flash write cycles.
    #RESTORE_DEFAULT_ON - Attempt to restore state and default to ON. Uses flash write cycles.
    #ALWAYS_OFF - Always initialize the pin as OFF on bootup. Does not use flash write cycles.
    #ALWAYS_ON - Always initialize the pin as ON on bootup. Does not use flash write cycles.
    on_turn_on:
      - light.turn_on:
          id: blue_led
          brightness: 100%
    on_turn_off:
      - light.turn_off: blue_led

output:
  - platform: esp8266_pwm
    id: red_output
    pin: GPIO0
    inverted: True
  - platform: esp8266_pwm
    id: blue_output
    pin: GPIO2
    inverted: True

light:
  - platform: monochromatic
    name: ${friendly_name} Red LED
    output: red_output
    id: red_led
    restore_mode: ALWAYS_OFF #Start with light off after reboot/power-loss event.
    #RESTORE_DEFAULT_OFF (Default) - Attempt to restore state and default to OFF if not possible to restore. Uses flash write cycles.
    #RESTORE_DEFAULT_ON - Attempt to restore state and default to ON. Uses flash write cycles.
    #ALWAYS_OFF - Always initialize the pin as OFF on bootup. Does not use flash write cycles.
    #ALWAYS_ON - Always initialize the pin as ON on bootup. Does not use flash write cycles.
    effects:
      - strobe:
      - flicker:
          alpha: 50% #The percentage that the last color value should affect the light. More or less the “forget-factor” of an exponential moving average. Defaults to 95%.
          intensity: 50% #The intensity of the flickering, basically the maximum amplitude of the random offsets. Defaults to 1.5%.
      - lambda:
          name: Throb
          update_interval: 1s
          lambda: |-
            static int state = 0;
            auto call = id(red_led).turn_on();
            // Transtion of 1000ms = 1s
            call.set_transition_length(1000);
            if (state == 0) {
              call.set_brightness(1.0);
            } else {
              call.set_brightness(0.01);
            }
            call.perform();
            state += 1;
            if (state == 2)
              state = 0;
  - platform: monochromatic
    name: ${friendly_name} Blue LED
    output: blue_output
    id: blue_led
    restore_mode: ALWAYS_OFF #Start with light off after reboot/power-loss event.
    #RESTORE_DEFAULT_OFF (Default) - Attempt to restore state and default to OFF if not possible to restore. Uses flash write cycles.
    #RESTORE_DEFAULT_ON - Attempt to restore state and default to ON. Uses flash write cycles.
    #ALWAYS_OFF - Always initialize the pin as OFF on bootup. Does not use flash write cycles.
    #ALWAYS_ON - Always initialize the pin as ON on bootup. Does not use flash write cycles.
    effects:
      - strobe:
      - flicker:
          alpha: 50% #The percentage that the last color value should affect the light. More or less the “forget-factor” of an exponential moving average. Defaults to 95%.
          intensity: 50% #The intensity of the flickering, basically the maximum amplitude of the random offsets. Defaults to 1.5%.
      - lambda:
          name: Throb
          update_interval: 1s
          lambda: |-
            static int state = 0;
            auto call = id(blue_led).turn_on();
            // Transtion of 1000ms = 1s
            call.set_transition_length(1000);
            if (state == 0) {
              call.set_brightness(1.0);
            } else {
              call.set_brightness(0.01);
            }
            call.perform();
            state += 1;
            if (state == 2)
              state = 0;

# Blink the red light if we aren't connected to WiFi. Could use https://esphome.io/components/status_led.html instead but then we couldn't use the red light for other things as well.
interval:
  - interval: 500ms
    then:
      - if:
          condition:
            not:
              wifi.connected:
          then:
            - light.turn_on:
                id: red_led
                brightness: 100%
                transition_length: 0s
            - delay: 250ms
            - light.turn_off:
                id: red_led
                transition_length: 250ms

Copy
substitutions:
  device_name: test_plug
  device_description: Power Monitoring plug used for testing
  friendly_name: Lab Test Plug
  ipaddress: 192.168.1.200
  wattage_calibration: 67.6 -> 11.0
  amperage_calibration: 0.12 -> 0.08
  voltage_calibration1: 0.0 -> 0.0
  voltage_calibration2: 322.4 -> 118.3

<<: !include aoycocr_x10s_common.yaml