devices.esphome.io

Alfawise SJ-7

Alfawise SJ-7

Device Type: misc
Electrical Standard: global
Board: esp8266

Alfawise SJ-7 (Essential oil diffuser)

alt text

Working

  • All essential oil diffuser related controls (ON/OFF; LOW/HIGH; Timer 1H/3H/6H).
  • Lava lamp lighting activation, fast/slow color change, I can add stop color change button if needed.
  • OTA upgrade.

Not Working

  • Use the light like a classic bulb (just on of off and choose a color).

Installation

Flashing

For flashing, you have to solder wires like this:

alt text Use U0TXD, U0RXD, GND (and VCC if you dont want to use the diffuser power supply).

Make sure to ground GPIO0 during boot.

You can use the ESPHome add-on from Home Assistant Community Add-ons

Basic Configuration

# Basic Config
substitutions:
name: alfawise
friendly_name: "alfawise SJ-7"
#commands
receive_timer1h: "55:AA:03:1F:09:01:2B"
receive_timer3h: "55:AA:03:1F:09:02:2C"
receive_timer6h: "55:AA:03:1F:09:03:2D"
receive_high: "55:AA:03:1F:07:02:2A"
receive_low: "55:AA:03:1F:07:01:29"
receive_lava_lamp: "55:AA:03:1F:02:01:24"
receive_rainbow_slow: "55:AA:03:1F:0C:01:2E"
receive_rainbow_fast: "55:AA:03:1F:0C:03:30"
receive_lava_lamp_on_diff: "55:AA:02:04:01:06"
receive_diff_on_switch: "55:AA:02:03:01:05"
receive_light_off_switch: "55:AA:02:04:00:05"
receive_light_diff_off_esp: "55:AA:02:1F:0E:2E"
receive_diff_off_esp: "55:AA:03:1F:07:00:28"
receive_light_off_esp: "55:AA:03:1F:02:00:23"
esphome:
name: ${name}
includes:
- uart_read_line_sensor.h
- fake_fan_output.h
on_boot:
priority: -100.0
then:
- switch.turn_off: power_high
- lambda: id(${name}_fan).speed = 0;
- switch.turn_off: lava_lamp
- switch.turn_on: wifi_blinkin_slow
- delay: 5s
- switch.turn_off: wifi_blinkin_slow
esp8266:
board: esp01_1m
debug:
# Enable logging
logger:
baud_rate: 0
level: debug
esp8266_store_log_strings_in_flash: False
ota:
password: "xxx"
uart:
id: uart_bus
tx_pin: GPIO1
rx_pin: GPIO3
baud_rate: 9600
stop_bits: 1
# debug:
# direction: BOTH
# dummy_receiver: false
# after:
# delimiter: "\n"
# bytes: 256
# sequence:
# - lambda: UARTDebug::log_hex(direction, bytes, ':');
wifi:
ssid: "xxx"
password: "xxx"
# Enable fallback hotspot (captive portal) in case wifi connection fails
ap:
ssid: "${friendly_name} Fallback Hotspot"
password: "xxx"
api:
web_server:
port: 80
# Sync time with Home Assistant.
time:
- platform: homeassistant
id: homeassistant_time
- platform: sntp
on_time:
# Every 1 seconds
- seconds: /1
then:
- if:
condition:
and:
- switch.is_off: power_low
- switch.is_off: power_high
- fan.is_on: ${name}_fan
then:
- switch.turn_on: update_fan_speed
else:
- if:
condition:
and:
- switch.is_on: power_low
- switch.is_off: power_high
- or:
- lambda: |-
if (id(${name}_fan).speed == 2) {
return true;
}else{
return false;
}
- lambda: |-
if (id(${name}_fan).speed == 0) {
return true;
}else {
return false;
}
then:
- switch.turn_on: update_fan_speed
else:
- if:
condition:
and:
- switch.is_off: power_low
- switch.is_on: power_high
- or:
- lambda: |-
if (id(${name}_fan).speed ==1) {
return true;
}else {
return false;
}
- lambda: |-
if (id(${name}_fan).speed == 0) {
return true;
}else {
return false;
}
then:
- switch.turn_on: update_fan_speed
# Text sensors with UART received information.
text_sensor:
- platform: custom
lambda: |-
auto uart_readline = new UartReadLineSensor(id(uart_bus));
App.register_component(uart_readline);
return {uart_readline};
text_sensors:
id: "uart_readline"
name: ${name} serial
- platform: wifi_info
ip_address:
name: ${name} ip
ssid:
name: ${name} ssid
bssid:
name: ${name} bssid
- platform: version
name: ${name} ESPHome Version
sensor:
# Uptime sensor
- platform: uptime
name: ${name} uptime
unit_of_measurement: days
update_interval: 300s
accuracy_decimals: 1
filters:
- multiply: 0.000011574
# WiFi Signal sensor
- platform: wifi_signal
name: ${name} signal
update_interval: 60s
accuracy_decimals: 0
switch:
- platform: template
id: timer1h
name: ${name} Timer 1H
icon: mdi:timer-sand-empty
disabled_by_default: false
optimistic: false
assumed_state: false
lambda: |-
if (id(uart_readline).state == "${receive_timer1h}") {
return true;
} else if(id(uart_readline).state == "${receive_timer3h}") {
return false;
} else if(id(uart_readline).state == "${receive_timer6h}") {
return false;
} else if(id(uart_readline).state == "${receive_light_off_switch}") {
return false;
} else if(id(uart_readline).state == "${receive_light_diff_off_esp}") {
return false;
} else if(id(uart_readline).state == "${receive_diff_off_esp}") {
return false;
} else {
return {};
}
turn_on_action:
then:
- if:
condition:
and:
- fan.is_off: ${name}_fan
then:
- fan.turn_on:
id: ${name}_fan
speed: 1
- delay: 500ms
- uart.write: [0x55, 0xAA, 0x03, 0x09, 0x01, 0x00, 0x0c]
- delay: 1h
- uart.write: [0x55, 0xaa, 0x03, 0x0e, 0x00, 0x00, 0x10]
- platform: template
id: timer3h
name: ${name} Timer 3H
icon: mdi:timer-sand-complete
disabled_by_default: false
optimistic: false
assumed_state: false
lambda: |-
if (id(uart_readline).state == "${receive_timer3h}") {
return true;
} else if(id(uart_readline).state == "${receive_timer1h}") {
return false;
} else if(id(uart_readline).state == "${receive_timer6h}") {
return false;
} else if(id(uart_readline).state == "${receive_light_off_switch}") {
return false;
} else if(id(uart_readline).state == "${receive_light_diff_off_esp}") {
return false;
} else if(id(uart_readline).state == "${receive_diff_off_esp}") {
return false;
} else {
return {};
}
turn_on_action:
then:
- if:
condition:
and:
- fan.is_off: ${name}_fan
then:
- fan.turn_on:
id: ${name}_fan
speed: 1
- delay: 500ms
- uart.write: [0x55, 0xAA, 0x03, 0x09, 0x02, 0x00, 0x0d]
- delay: 3h
- uart.write: [0x55, 0xaa, 0x03, 0x0e, 0x00, 0x00, 0x10]
turn_off_action:
then:
- if:
condition:
and:
- fan.is_on: ${name}_fan
then:
- uart.write: [0x55, 0xAA, 0x03, 0x09, 0x01, 0x00, 0x0c]
- platform: template
id: timer6h
name: ${name} Timer 6H
icon: mdi:timer-sand
disabled_by_default: false
optimistic: false
assumed_state: false
lambda: |-
if (id(uart_readline).state == "${receive_timer6h}") {
return true;
} else if(id(uart_readline).state == "${receive_timer1h}") {
return false;
} else if(id(uart_readline).state == "${receive_timer3h}") {
return false;
} else if(id(uart_readline).state == "${receive_light_off_switch}") {
return false;
} else if(id(uart_readline).state == "${receive_light_diff_off_esp}") {
return false;
} else if(id(uart_readline).state == "${receive_diff_off_esp}") {
return false;
} else {
return {};
}
turn_on_action:
then:
- if:
condition:
and:
- fan.is_off: ${name}_fan
then:
- fan.turn_on:
id: ${name}_fan
speed: 1
- delay: 500ms
- uart.write: [0x55, 0xAA, 0x03, 0x09, 0x03, 0x00, 0x0e]
- delay: 6h
- uart.write: [0x55, 0xaa, 0x03, 0x0e, 0x00, 0x00, 0x10]
turn_off_action:
then:
- if:
condition:
and:
- fan.is_on: ${name}_fan
then:
- uart.write: [0x55, 0xAA, 0x03, 0x09, 0x01, 0x00, 0x0c]
- platform: template
id: power_high
icon: mdi:fan
disabled_by_default: true
optimistic: false
assumed_state: false
lambda: |-
if (id(uart_readline).state == "${receive_high}") {
return true;
} else if (id(uart_readline).state == "${receive_diff_on_switch}") {
return true;
} else if(id(uart_readline).state == "${receive_light_off_switch}") {
return false;
} else if(id(uart_readline).state == "${receive_light_diff_off_esp}") {
return false;
} else if(id(uart_readline).state == "${receive_diff_off_esp}") {
return false;
} else {
return {};
}
turn_on_action:
- uart.write: [0x55, 0xAA, 0x03, 0x07, 0x02, 0x00, 0x0B]
turn_off_action:
- uart.write: [0x55, 0xaa, 0x03, 0x07, 0x00, 0x00, 0x09]
on_turn_on:
- switch.template.publish:
id: power_low
state: OFF
on_turn_off:
- switch.template.publish:
id: power_low
state: OFF
- platform: template
disabled_by_default: true
id: power_low
icon: mdi:fan
optimistic: false
assumed_state: false
lambda: |-
if (id(uart_readline).state == "${receive_low}") {
return true;
} else if(id(uart_readline).state == "${receive_light_off_switch}") {
return false;
} else if(id(uart_readline).state == "${receive_light_diff_off_esp}") {
return false;
} else if(id(uart_readline).state == "${receive_diff_off_esp}") {
return false;
} else {
return {};
}
turn_on_action:
- uart.write: [0x55, 0xaa, 0x03, 0x07, 0x01, 0x00, 0x0A]
turn_off_action:
- uart.write: [0x55, 0xaa, 0x03, 0x07, 0x00, 0x00, 0x09]
on_turn_on:
- switch.template.publish:
id: power_high
state: OFF
on_turn_off:
- switch.template.publish:
id: power_high
state: OFF
- platform: template
disabled_by_default: true
id: wifi_blinkin_slow
icon: mdi:led-on
optimistic: true
assumed_state: true
turn_on_action:
- uart.write: [0x55, 0xaa, 0x03, 0x03, 0x03, 0x00, 0x08]
turn_off_action:
- uart.write: [0x55, 0xaa, 0x03, 0x03, 0x01, 0x00, 0x06]
- platform: template
name: ${name} Lava Lamp
id: lava_lamp
icon: mdi:lava-lamp
optimistic: false
assumed_state: false
lambda: |-
if (id(uart_readline).state == "${receive_lava_lamp}") {
return true;
} else if (id(uart_readline).state == "${receive_lava_lamp_on_diff}") {
return true;
} else if(id(uart_readline).state == "${receive_light_off_switch}") {
return false;
} else if(id(uart_readline).state == "${receive_light_diff_off_esp}") {
return false;
} else if(id(uart_readline).state == "${receive_light_off_esp}") {
return false;
} else {
return {};
}
turn_on_action:
- uart.write: [0x55, 0xaa, 0x03, 0x02, 0x00, 0x01, 0x05]
- uart.write: [0x55, 0xaa, 0x03, 0x02, 0x01, 0x01, 0x06]
turn_off_action:
- uart.write: [0x55, 0xaa, 0x03, 0x02, 0x00, 0x01, 0x05]
on_turn_on:
- switch.template.publish:
id: rainbow_fast
state: OFF
- switch.template.publish:
id: rainbow_slow
state: OFF
on_turn_off:
- switch.template.publish:
id: rainbow_fast
state: OFF
- switch.template.publish:
id: rainbow_slow
state: OFF
- platform: template
name: ${name} Rainbow Slow
id: rainbow_slow
icon: mdi:lightbulb-multiple
optimistic: false
assumed_state: false
lambda: |-
if (id(uart_readline).state == "${receive_rainbow_slow}") {
return true;
} else if(id(uart_readline).state == "${receive_light_off_switch}") {
return false;
} else if(id(uart_readline).state == "${receive_light_diff_off_esp}") {
return false;
} else if(id(uart_readline).state == "${receive_light_off_esp}") {
return false;
} else {
return {};
}
turn_on_action:
- uart.write: [0x55, 0xaa, 0x03, 0x02, 0x00, 0x01, 0x05]
- uart.write: [0x55, 0xaa, 0x03, 0x0c, 0x01, 0x00, 0x0f]
turn_off_action:
- uart.write: [0x55, 0xaa, 0x03, 0x02, 0x00, 0x01, 0x05]
on_turn_on:
- switch.template.publish:
id: rainbow_fast
state: OFF
- switch.template.publish:
id: lava_lamp
state: OFF
on_turn_off:
- switch.template.publish:
id: rainbow_fast
state: OFF
- switch.template.publish:
id: lava_lamp
state: OFF
- platform: template
name: ${name} Rainbow Fast
id: rainbow_fast
icon: mdi:lightbulb-group
optimistic: false
assumed_state: false
lambda: |-
if (id(uart_readline).state == "${receive_rainbow_fast}") {
return true;
} else if(id(uart_readline).state == "${receive_light_off_switch}") {
return false;
} else if(id(uart_readline).state == "${receive_light_diff_off_esp}") {
return false;
} else if(id(uart_readline).state == "${receive_light_off_esp}") {
return false;
} else {
return {};
}
turn_on_action:
- uart.write: [0x55, 0xaa, 0x03, 0x02, 0x00, 0x01, 0x05]
- uart.write: [0x55, 0xaa, 0x03, 0x0c, 0x03, 0x00, 0x11]
turn_off_action:
- uart.write: [0x55, 0xaa, 0x03, 0x02, 0x00, 0x01, 0x05]
on_turn_on:
- switch.template.publish:
id: lava_lamp
state: OFF
- switch.template.publish:
id: rainbow_slow
state: OFF
on_turn_off:
- switch.template.publish:
id: lava_lamp
state: OFF
- switch.template.publish:
id: rainbow_slow
state: OFF
- platform: template
disabled_by_default: true
id: update_fan_speed
optimistic: True
turn_on_action:
then:
- delay: 500ms
- if:
condition:
and:
- switch.is_off: power_low
- switch.is_off: power_high
then:
- fan.turn_off: ${name}_fan
else:
- if:
condition:
and:
- switch.is_on: power_low
- switch.is_off: power_high
then:
- fan.turn_on:
id: ${name}_fan
speed: 1
else:
- if:
condition:
and:
- switch.is_off: power_low
- switch.is_on: power_high
then:
- fan.turn_on:
id: ${name}_fan
speed: 2
- switch.turn_off: update_fan_speed
output:
- platform: custom
type: float
outputs:
id: fanoutput
lambda: |-
auto ${name}_fan = new FakeFanOutput();
App.register_component(${name}_fan);
return {${name}_fan};
fan:
- platform: speed
output: fanoutput
id: ${name}_fan
name: "${friendly_name} Fan"
speed_count: 2
on_turn_on:
then:
- if:
condition:
lambda: return (id(${name}_fan).speed == 0);
then:
- fan.turn_on:
id: ${name}_fan
speed: 1
- switch.turn_on: power_low
- delay: 500ms
- switch.turn_on: timer1h
else:
- if:
condition:
lambda: return (id(${name}_fan).speed == 1);
then:
- switch.turn_on: power_low
else:
- if:
condition:
lambda: return (id(${name}_fan).speed == 2);
then:
- switch.turn_on: power_high
- if:
condition:
and:
- switch.is_off: timer1h
- switch.is_off: timer3h
- switch.is_off: timer6h
then:
- delay: 500ms
- switch.turn_on: timer1h
on_turn_off:
then:
- lambda: id(${name}_fan).speed = 0;
- switch.turn_off: power_low
- switch.turn_off: power_high
on_speed_set:
then:
- if:
condition:
and:
- lambda: return (id(${name}_fan).speed == 0);
- or:
- switch.is_on: power_low
- switch.is_on: power_high
then:
- switch.turn_off: power_high
- switch.turn_off: power_low
else:
- if:
condition:
- lambda: return (id(${name}_fan).speed == 1);
- switch.is_off: power_low
then:
- switch.turn_on: power_low
else:
- if:
condition:
- lambda: return (id(${name}_fan).speed == 2);
- switch.is_off: power_high
then:
- switch.turn_on: power_high
- if:
condition:
and:
- switch.is_off: timer1h
- switch.is_off: timer3h
- switch.is_off: timer6h
then:
- delay: 500ms
- switch.turn_on: timer1h
captive_portal:

fake_fan_output.h

#include "esphome.h"
using namespace esphome;
class FakeFanOutput : public Component, public FloatOutput {
public:
void write_state(float state) override {
if (state < 0.1) {
// OFF
} else if (state < 0.5) {
// low speed
} else {
// high speed
}
}
};

uart_read_line_sensor.h

#include "esphome.h"
static int pos = 0;
char outputBuffer[3];
const int max_line_length = 80;
static char buffer[max_line_length];
int j = 0;
int startMarker = 0x55;
int secondMarker = 0xAA;
int timeOut = 50;
bool receiveUntilTimeout;
bool valuesending = false;
int timeReceived;
class UartReadLineSensor : public Component, public UARTDevice, public TextSensor {
public:
UartReadLineSensor(UARTComponent *parent) : UARTDevice(parent) {}
// Helper function for converting byte value to 2-digit hex string
void byte2HexStr(byte val, char* outputBuffer){
const char HEX_DIGITS[17] = "0123456789ABCDEF";
byte upper_nibble_index = (val & 0xf0) >> 4;
byte lower_nibble_index = val & 0xf;
outputBuffer[0] = HEX_DIGITS[upper_nibble_index];
outputBuffer[1] = HEX_DIGITS[lower_nibble_index];
outputBuffer[2] = '\0';
}
void setup() override {
// nothing to do here
}
int sendvalue(char* buffer, bool valuesending)
{
valuesending = true;
std::string myStrObject;
myStrObject = "";
// buffer size
for(int i = max_line_length; i > 0; i--) {
if (j == 0) {
if (buffer[i] > 0 ) {
j = i + 1;
break;
}
}
}
// convert to hex
for(int i = 0; i < j; i++) {
byte2HexStr(buffer[i], outputBuffer);
myStrObject += outputBuffer;
// add separator except for the last element
if(i < j - 1) {
myStrObject += ":";
}
}
// publish result
publish_state(myStrObject.c_str());
// reset var
j = 0;
pos = 0;
for( int i = 0; i < max_line_length + 1; ++i )
buffer[i] = (char)0;
valuesending = false;
return 1;
}
// Store values
int storevalue(char* buffer, int readch, bool UntilTimeout, bool valuesending)
{
while (valuesending == true) {
delay(200);
}
buffer[pos++] = readch;
buffer[pos] = 0;
if (UntilTimeout) {
receiveUntilTimeout = true;
}
timeReceived = millis();
return 1;
}
void loop() override {
int readch;
if (available() >= 1 && !receiveUntilTimeout) {
readch = Serial.read();
if (readch == startMarker) {
storevalue(buffer, readch, true, valuesending);
}
}
if (receiveUntilTimeout) {
if (Serial.available() > 0)
{
readch = Serial.read();
if (readch == startMarker) {
sendvalue(buffer,valuesending);
}
if (readch == secondMarker) {
if (pos > 1 ) {
sendvalue(buffer,valuesending);
storevalue(buffer, 0x55, false, valuesending);
}
}
storevalue(buffer, readch, false, valuesending);
}
else //Serial.available == 0 and nothing to read
{
if (millis() - timeReceived >= timeOut)
{
receiveUntilTimeout = false;
sendvalue(buffer,valuesending);
}
}
}
}
};

Home Assistant integration

Lovelace card

For lovelace card, you need this HACS Addons :

File diffuser.png need to be in this path : config/www/

Card config example

type: custom:vertical-stack-in-card
cards:
- type: picture-entity
entity: switch.schedule_lave_linge
image: /local/diffuser.png
show_state: false
show_name: false
tap_action:
action: none
hold_action:
action: none
- type: entities
entities:
- entity: fan.alfawise_sj_7_fan
type: custom:fan-percent-button-row
name: Diffuser
state_color: true
isTwoSpeedFan: true
customSetpoints: true
reverseButtons: true
sendStateWithSpeed: false
lowPercentage: 50
hiPercentage: 100
width: 35px
height: 35px
- type: custom:paper-buttons-row
buttons:
- layout: icon|name
icon: mdi:clock-time-two
name: Timer
style:
button:
width: 150%
justify-content: left
tap_action:
action: none
- entity: switch.alfawise_timer_1h
layout: name
name: 1H
style:
button:
width: 17%
- entity: switch.alfawise_timer_3h
layout: name
name: 3H
style:
button:
width: 17%
- entity: switch.alfawise_timer_6h
layout: name
name: 6H
style:
button:
width: 17%
- type: custom:paper-buttons-row
buttons:
- layout: icon|name
icon: mdi:lightbulb
name: Light
style:
button:
width: 150%
justify-content: left
tap_action:
action: none
- entity: switch.alfawise_lava_lamp
layout: icon
style:
button:
width: 15%
- entity: switch.alfawise_rainbow_slow
layout: icon
style:
button:
width: 15%
- entity: switch.alfawise_rainbow_fast
layout: icon
style:
button:
width: 15%

Lovelace card screenshot

alt text

Original firmware

I have put a backup of the original firmware, and I also modified the AMA HOME APK but only for reconnect the original firmware to Wifi, ssg360 seems down.

https://github.com/antibill51/Alfawise_SJ-7_HASSIO/tree/master/Original%20firmware

Edit this page on GitHub